Skip to main content

A Day of Giving, Dec 19: Volunteer (opens in a new tab) or donate (opens in a new tab)

Arizona licensed · $1M/$2M general liabilityServing Arizona homeowners since 2005Peoria design showroomWritten, itemized project scopesProject-specific payment & warranty terms

Pool Remodel in Gilbert, AZ

Reviewed by the AE Outdoor Living team · Updated Nov 20, 2026

Short answer: Start a Gilbert pool remodel by deciding what to keep. We check the shell, plumbing, deck elevations and equipment before choosing an interior finish. If you want a spa or a larger deck, we also check where stormwater collects, how the pool enclosure works and what the Town needs to review.

Call (623) 300-2589

What should we look at before resurfacing a Gilbert pool?

We start with the part of the pool you want to change and work outward. If the floor feels rough underfoot but you like the depth, entry and seating, resurfacing may be the right scope. If getting down the steps is the problem, a different finish alone will leave you with the same step heights.

At the pool edge, look where the interior meets the waterline tile and where the tile meets the coping, the cap you hold when climbing out. Point out any loose pieces, uneven edges or cracks that cross from one material into another. We record their locations and discuss what a closer look would require. If the shell needs structural evaluation, we address that before specifying a new finish.

We also ask which parts of the deck you want to keep. A plumbing route that crosses a patio changes how much surface has to come up and what can be put back. Our pool remodeling overview lays out the choices you can bring to that conversation.

Which decisions change the scope of a spa addition?

Choose the spa location by looking at the pool, the equipment and the deck you use together. Mark out its footprint, then walk from the back door to the pool steps. Pull out a patio chair. A spa can fit inside the property lines and still take the space you need to get around the table with a wet towel and a child in tow.

At the equipment pad, we check what serves the existing pool and what the proposed jets and heat source will need. A shared system has to support both pool and spa operation. Moving the pad also changes pipe routes and the space needed to reach a filter lid or remove a heater panel. We identify the surfaces along that route in the scope so you can compare two locations on equal terms.

If you are deciding whether to keep the existing shell at all, compare the layout with your options for a new Gilbert pool. For a second property across the town line, our Mesa pool remodel guide covers the questions to take to Mesa.

Keep the existing layout or make room for a spa? Get an instant price range, then book an on-site design consultation or call (623) 300-2589.

Where will the water go if we widen the deck?

Follow the water from the patio to the low spot in the yard before extending the deck into it. Gilbert's residential pool and spa checklist calls for a grading and drainage plan on lots that must retain runoff on site. The Town directs applicants to confirm whether that condition applies to their subdivision.

Bring a plot plan if you have one, and show us where water collected during the last desert storm. A shallow depression that looks like unused space on a dry afternoon may be where the yard stores runoff. We check how a proposed spa, deck or raised edge would affect that space and the route water takes to reach it. That can change which side of the pool makes sense for the addition.

What will Gilbert want to see for permits and the barrier?

For a permitted pool or spa alteration, start with the Town's residential checklist and describe the actual changes. It calls for a drawing locating the water and the equipment, applicable utility diagrams, and structural details or authorization to use a standard plan on file. Gilbert's residential permit instructions explain how to submit through One Stop Shop. Licensed trades perform structural, gas and electrical work per the signed scope. Permits are per signed scope.

For the barrier, identify which walls and gates enclose the water. Gilbert's pool barrier guidance measures a property fence from the side away from the pool. It calls for three feet of clearance between the fence and easily climbed features such as a raised planter. If the deck height changes at a gate, check the new clearance and make sure the gate can close and latch on its own.

Show any proposed interior fence separately. Gilbert's Technical Codes, section 10-31-4, amend residential code provision R105.2 to limit the fence permit exemption to fences up to three feet high. If you want an open view from the patio, explore frameless glass pool fencing in Gilbert and confirm with the Town which enclosure will serve as the required barrier.

Frequently asked questions

Is a permit needed to resurface a pool in Gilbert?
Ask Gilbert Development Services with the proposed work in writing. The Town's pool and spa checklist describes what to submit for permitted work. It does not give a blanket answer for replacing only an interior finish. Specify whether the work includes tile, altered steps, new plumbing, a change at the equipment pad or a different barrier.
Can a spa be added to an existing pool?
Yes, when the shell, lot and equipment can support the design. We look at the connection to the pool, space for seating, the route for new lines and access to the equipment. If a spillway is part of the design, choose its direction with the view and sound from the patio in mind.
What should I check before choosing a finish?
Handle a wet sample and pay attention to the texture against your palm, particularly for benches and steps. Take the tile and coping samples outside together and view them in both sun and shade. Water depth and light affect the color you see, so a dry sample indoors gives only part of the picture.
How does the HOA process fit in?
Gilbert's permit application directs homeowners to ask their HOA about its requirements. For a home in a master-planned community, request the current architectural guidelines and ask what the reviewer needs for changes visible over the wall, equipment screening and access across common land. Our guide to HOA backyard approval can help you prepare the submission.

Sources

Ready to plan it?


ROC #340966 (R-62) · #341002 (R-3) · #347738 (KA-5) · #211530 (CR-21) · Company facts

Related guides

Keep learning before you build.