Skip to main content

A Day of Giving, Dec 19: Volunteer (opens in a new tab) or donate (opens in a new tab)

Arizona licensed · $1M/$2M general liabilityServing Arizona homeowners since 2005Peoria design showroomWritten, itemized project scopesProject-specific payment & warranty terms

Patio Cover Cost in Arizona: What Drives the Price

Reviewed by the AE Outdoor Living team · Updated Nov 19, 2026

Short answer: A patio cover's price comes from the roof type, the span and beam sizes, how it attaches to the house, the footings, the roof loads, the permit path and any fans, lights or drainage. A cover that ties into rafter tails or carries tile needs structural calculations. Your range comes from the PriceGuide instant quote.

Call (623) 300-2589

We don't publish a patio cover price range, and we'd be guessing if we did. Two covers the same size can land far apart because of how they meet the house. What we can do is show you what moves the number, so the range PriceGuide gives you makes sense and the written proposal holds no surprises.

What does the roof type change?

The roof is the first fork. A lattice or slatted roof filters sun and carries little load. A solid roof gives full shade and sheds rain. An insulated roof panel keeps heat off the patio and the wall behind it. A louvered roof opens and closes, adds motors and controls and needs power. Each step up carries more weight and catches more wind, so it changes the beams, posts and footings under it as well as the roof itself. Our comparisons of solid, lattice and louvered covers and insulated and non-insulated aluminum go deeper.

How does the span change cost?

A wider opening between posts needs a deeper beam. A deeper cover, measured out from the house, needs longer rafters and can need a beam in the middle. Fewer posts look cleaner but load the remaining ones harder. We balance post spacing against the view and the beam size against the look you want.

Want a number for your cover? Get an instant price range. It's an educational range, not a quote. Or book an on-site design consultation and we'll measure the span and check your roofline. Call (623) 300-2589.

Why does the attachment to the house matter so much?

Because it decides how much engineering the cover needs. The City of Phoenix Residential Patio Covers Guideline says structural calculations aren't required when the patio rafters don't connect to the house's rafter tails, the roof loads stay within its light design criteria and the cover is conventionally framed. Tile roofing on the cover is outside those criteria. Chandler's permit manual goes further: rafters can't attach to the fascia or truss tails at all; they bear on the wall top plate or a ledger bolted to the studs, with stucco removed first.

The Phoenix guideline also notes that the headers over existing openings in the wall behind the cover may need to be checked, depending on the house and the depth of the cover. A big slider or a wide window under the new cover can add work inside the wall.

What about footings?

Every post sits on a footing. Phoenix's guideline sets a minimum depth of 12 inches below undisturbed ground, a presumptive soil bearing value and a minimum concrete strength. A heavier roof, a wider span or poor soil means bigger footings. Caliche can slow the digging, which our caliche guide explains.

How do permits and reviews affect the price?

In the cities we checked, an attached patio cover is permitted work; Mesa says a permit may be required for light metal covers. Phoenix requires drawings showing setbacks and lot coverage, a cross section, a roof framing plan and a foundation plan, and charges permit and plan review fees. Hillside lots need grading and drainage approval first, historic districts need preservation approval and floodplain lots need floodplain approval. Each review adds drawings and coordination.

Some cities offer standard details for simple covers. Scottsdale's attached patio cover details, for example, apply to one-story covers up to 12 feet tall and open on two or more sides. A cover that fits those details takes less engineering than one that doesn't.

What do fans, lights and drainage add?

Power for fans, lights, heaters or a louvered roof is electrical work with its own permit. Gutters and downspouts send roof water where the lot drains instead of onto the patio. Near a pool, Chandler requires metal covers within 5 feet of the water to be bonded to the pool's bonding system. Each one is a line on the proposal.

Who builds it?

One contract, one AE team managing every trade. We're a Belgard Master Craftsman, certified installers for Belgard, Phoenix Paver and Acker-Stone, ICPI-trained and a CMHA certified installer. David Bell, AE's owner, is President of the Southwest Hardscapes Association. Serving Arizona homeowners since 2005, licensed under Arizona ROC 211530, 347738, 341002 and 340966. Warranty terms are on AE's warranty page. See pergolas and shade and patio covers in Phoenix.

How do I get a number?

Start with PriceGuide for an instant range. A written proposal for your house follows the on-site assessment.

Frequently asked questions

Why doesn't AE publish a patio cover price range?
Because the attachment, span and permit path vary too much by house. PriceGuide gives a range for your project.
Does a solid roof cost more than lattice?
It carries more load, so the beams, posts and footings are larger.
When does a patio cover need structural calculations?
In Phoenix, when rafters tie into rafter tails, loads exceed the light criteria or framing isn't conventional.
Do fans and lights need a separate permit?
Yes. They're electrical work.

Ready to plan it?

Binding pricing comes only from a written proposal signed by an AE representative. Your signed proposal and agreement control scope, price, warranty and permit responsibilities.


AE Outdoor Living · Arizona licensed · ROC 211530 · ROC 347738 · ROC 341002 · ROC 340966 (company facts) · 9715 W Peoria Ave, Peoria, AZ 85345 · (623) 300-2589

Related guides

Keep learning before you build.